sock swt sing vert 10a shutt

Socket Outlets Switched Vertical, Standard Size, 250V, 10A

Catalogue Number: 15VS
Colour White Electric (WE)
  • White Electric 1 PCE 1


hide show
Number of Units in Package 1
Number of Units in Package 2
Number of Units in Package 3
Package 1 width
73 mm
Package 2 Height
118 mm
Package 2 Length
167 mm
Package 2 width
148 mm
Package 3 Height
254 mm
Package 3 Length
445 mm
Package 3 width
348 mm
Package 1 Height
14 mm
Package 1 Length
115 mm
Unit Type of Package 1
Unit Type of Package 2
Unit Type of Package 3
Product brand
Range of product
Standard Series
Control type
ON/OFF button
Number of gangs
1 gang
Pin number
Number of power socket outlets
  • switch
  • rocker
    • Mounting position
      Fixing mode
      by screws
      Local signalling
      without light indicator
      PC (polycarbonate)
      Surface finish
      [Ue] rated operational voltage
      250 V AC
      [In] rated current
      10 A
      14 mm
      115 mm
      73 mm
      Fixing center
      84 mm
    • AS/NZS 3100
    • AS/NZS 3112
    • AS/NZS 3133
    • AS/NZS 3000:approval number S/1
      • Package 1 Weight
        0.082 kg
        Package 2 Weight
        0.82 kg
        Package 3 Weight
        8.2 kg
        Sustainable offer status
        Green Premium product
        REACh Regulation
        Free of Substances of Very High Concern above the threshold
        EU RoHS Directive
        Mercury free
        RoHS exemption information
        China RoHS Regulation
        Product out of China RoHS scope. Substance declaration for your information
        Environmental Disclosure

        Frequently Asked Questions

        hide show

        What is the inrush current of a LC1D40U7 Contactor?

        It is 160VA inrush and 15VA sealed at 50HZ for the LC1D40U7 Contactor.
        For more information see data sheet

        Do you have a 15S in biege?

        No, the 15S only comes in White Electric and Red.

        Some of the key features are:
        • 1 pole
        • Standard size
        • Safety shutter
        For further information please visit

        What is the maximum DC voltage per pole for TeSys F Range contactors.

        The maximum DC voltage for TeSys F range contactors is 125 Volt per pole. This voltage is applicable for the specification of L/R <= 15ms in DC applications.

        What is the maximum DC voltage per pole for TeSys D range contactors.

        The maximum DC voltage for TeSys D range contactor is 75 Volt per pole. This voltage is applicable for the specification of L/R <= 15ms in DC applications.

        How does the Test Button on the RH99 work?

        When the test push button is activated the switch SW1 is moved on Test position. The measurement of the network is temporarily stopped during 15ms and a sinusoidal signal of 500Hz to simulate a trip is sent to create a current of 100µA inside the resistor R. The signal seen by the toroid sensor is really negligible about the test signal injection.
        During the test signal injection the settings are: Idn = 30mA and tfault = 0.
        At the end of the 15ms delay
        -> if the product trips (TEST OK) the fault LED and the Fault order relay are activated (in case of no trip test only the fault LED is activated). We have to push on the push button Reset to remove the failure create by the test (in case of automatic reset product no action need to remove the failure).
        -> if the product doesn’t trip, no LED, no relay order the TEST is NOK and it means the product doesn’t work.
        After the 15ms of test signal injection the switch SW1 comes back to the measure position and re-starts the monitor of the network with the customer settings (in the front face).
        So if a trip occurs during the test, it will be see directly after the 15ms of test signal injection and it will be impossible to remove the failure state by a push on Reset push button.
        The toroids used on the Vigirex range have only one winding inside.   
        There is no Calibration procedure for this product. The product is designed to provide the accuracy specified on the catalogue for the product life time.


        What is the minimum pulse width or duration required on a IOX or IOC module to register an input status change on the CM4000 series meter?

        Minimum pulse or duration required on a IOX or IOC module on a CM4000 series meter

        Product Line
        CM4000 series meter

        Hardware Specifications

        The minimal pulse duration per input on the CM4000 IOX or IOC is 15ms when the control power to the meter is DC voltage. For AC voltage to the control power the minimal input pulse duration is 23ms.
        Show More