box wall deep 4g sing height

WALL BOX DEEP 4 GANG SINGLE HEIGHT

Catalogue Number: 164/4
box wall deep 4g sing height
Colour:
Colour: Per UOM Std.
  • 1 PCE 1

Specifications

hide show
Range of product
Series 164
Product brand
Clipsal
Shape
rectangular
Number of gangs
4 gangs
Cable entry number
26
Material
steel
Surface treatment
electro-galvanized
Length
188 mm
Width
97 mm
Depth
58 mm
Location of connection
rear

Frequently Asked Questions

hide show

What is the wall box to suit the B8/30/4

 The wall box part number is 164/4

What are the dimensions of wall box 164/4 and the part number to suit?

The 164/4 which is the wall box to suit part number B8/30/4.

dimensions  188mm x 97mm x 58 mm

What is the alternate code for a 164/3

There is no plastic box the same size as 164/3, you can use PDL144Mt side by side would do the same

What is the wall box to suit the B4/30/2 ?

 The part number for the wall box is 164/2

What are the dimensions of the 164/5 wall box?

The dimensions of the 164/5 wall box are 234mm wide x 97mm high x 58mm deep.

Some of the key features are:
  • Fixed nut
  • 5 gang
  • Standard size
  • for poured concrete
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=164/5

What is the wall box to suit the B6/30/3 ?

 The part number for the wall box is 164/3

What is the wall box to suit the B10/30/5 ?

 The part number for the wall box 164/5

What are the dimensions for part number 162/4?

The dimensions are 186mm (w) x 194mm (h) x 58mm (d)

for more information on this part please refer to https://www.clipsal.com/Trade/Products/ProductDetail?catno=162/4

User-added image

What are the dimensions of wall box to suit 14/30/7

Dimensions of wall box 324mm x 97mm x 58mm Part no 164/7

What is the part number for the wall box for the 14/30/7 and dimensions?

The part number for the wall box for the 14/30/7 and dimensions are - 164/7 & dimensions - W324mm x H97mm x D58mm

For further information , visit link below:-
https://www.clipsal.com/Trade/search-results?q=14/30/7

User-added image

What are the dimensions of the wall box to suit the B12/30/6 Multi-Gang Switch?

The wall box to suit the 12/30/6 Multi-Gang Switch is a 164/6.

The dimensions of the wall box is a 164/6 are 278mm(W) X 97mm(H) X 58mm(D).

Some of the key features are:

  • 30 series rocker type
  • B-Style
  • Switch arrangement 6 horizontal and 2 vertical
  • Fascia size: 303 mm Width x 120 mm Height
  • 12 number of switch apertures


For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=B12/30/6

What is the replacement for 16468 CT?

The replacement for 16468 CT is METSECT5MF025
 

What is the current transformers with accuracy class 0.5rated power: 3 VA?

 The part code is 16455

What is the part code for a Surge arrestor 3P neutral needed that indicates tripping

 The part code you need is a 16564

Is cover available to suit 645/4?

Yes we do have a cover and the part number is 645/4COVER-BK.

Is there any bracket available for a 2000/4?

There is no stud bracket, you could use the 2154/4 mounting clip.

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=2154/4

What is the replacement for the Merlin Gerin Current Transformer 16456?

The Part code is METSECT5CC020.
https://eshop.schneider-electric.com/product.aspx?org=21&lang=1&dist=276&prod_id=METSECT5CC020

What is the continuous current rating of a CA2K relay?

Issue:
What is the continuous current rating of a CA2K relay?

Product Line:
Tesys Relays

Environment:
All Products

Cause:
Product Features

Resolution:
10 Amperes.


CTA-ID : 15484

What is the part number for a lid to suit the 265/4 ?

The part number is 265/4LID-GY
For more information on this product range please visit the Clipsal web site on the link provided
https://www.clipsal.com/Trade/search-results?q=265/4

What wall clip is used for Prestige large format plates?

The 154/2 is the clip to suit any Prestige large format plate 115mm x 115mm

Part number for a C clip to suit prestige range?

The part name is 154/2

Is there a 154 C-clip that does thicker than 10mm plasterboard/ gyprock?

Yes the 154/1 does plasterboard/gyprock thickness's between 19-25mm.

What is the difference between the Surge Arresters reference 15597 and 16447

The difference between the Surge Arrester references 15597 and 16447 is as follows:

1.) 15597 is a PF20 3Pole Fixed type Type 2 LV Surge Arrester.
2.) 16447 is a PRD20 3Pole Withdrawable type Type 2 LV Surge Arrester. 

Both are suitable to be used in low risk level and for use in TNC Earthing systems.

The difference is that 15597 at its end of life needs to be replaced as it is Fixed type, while 16447 at its end of life can be reused by simply replacing the cartridge as it is Withdrawable type, and the other major advantage is that the wiring does not get disturbed.

What is the part number for the replacment to 16451?

The replacement to the 16451 is new part number - METSECT5CC005
For further information please visit the link:
 https://eshop.schneider-electric.com/product.aspx?org=21&lang=1&dist=276&prod_id=METSECT5CC005
 
User-added image

What is the maximum number of counts available from the multiturn encoder for Lexium Integrated Drives?

The optional multiturn absolute encoder for Lexium ILA and ILS drives has the following maximum counts.
16384 counts x 4096 turns - 1 = total maximum counts of 67108863

What is the difference between a 9001KYSS2 and a 9001KYSS200?

Issue:
What is the difference between a 9001KYSS2 and a 9001KYSS200?

Product Line:
Control Stations

Environment:
All products

Cause:
Product Features

Resolution:
The 9001 KYSS2 is a 2 hole stainless steel control station enclosure. The 9001 KYSS200 indicates a custom assembled pushbutton station built with the KYSS2 enclosure. The 9001KYSS200 requires a key sheet be filled out.


CTA-ID : 13484

Does the 554C4 have new 4 single screw connectors instead of the original two screw connectors?

Over the coming months, the terminal connectors supplied with a number of Electrical Accessories will be changing. These changes are:
 
  1. The screw type in the connector will suit either a No. 2 Philips Drive or a No 1 Square Drive screwdriver.
 
  1. Terminal connectors will now be square wrapper design, ensuring reliable connection.
 
  1. All connectors will now be supplied with single screw. This is fully compliant with AS/NZS3000:2007 as per clause (d) below from sub-section 2.9.4. for active, neutral and earth connections.
(d) a neutral conductor used as a combined protective earthing and neutral (PEN) conductor for protective earthing of any portion of an electrical installation, the terminal shall be of a type having—
  1. two screws; or
  2. one screw with an outside diameter not less than 80% of the tunnel diameter.
 
The terminal connectors being supplied have a screw diameter in excess of 80% of the tunnel diameter which means the single screw connectors can be used for active, neutral and earth connections.
 
The products supplied with new connectors are:
  • 504/4
  • 554/3
  • 554/4
  • 554J4
  • 554C4
  • 554J4B100
  • HD554J4

What is the part number of the wall clip suitable for large format Prestige P2000 plates?

The part number for the wall clip suitable for large format Prestige P2000 plaes is 154/2.

Do you have the a longer version of the standard mounting screws for your power points?

Yes the part number for the longer screws is a 355A. They are 50mm long apposed  to the 355 which is 32mm long. Both screws are M3.5 X 0.8 Pitch.

What is the part no for the lid only as a spare of a 265/4?

The part no is 265/4LID

Please see the following link for further details: https://www.clipsal.com/Trade/Products/ProductDetail?catno=265/4LID

User-added image

What is the part number for the lid to suit the adaptable box 265/4?

The part number for the lid to suit the 265/4 adaptable box is - 265/4LID.

Some of the key features are:

  • For adaptable box 265/4
  • Grey colour
  • IP56

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=265/4LID


 

 

ATV61: Is there a way to monitor or read the DC bus on the drive HMI?

Issue:
ATV61: Is there a way to monitor or read the DC bus on the drive HMI?

Product Line:
Altivar 61/71  ATV61 ATV71

Environment:
All

Cause:
Limited access to terminals

Resolution
There are no monitoring options for reading the DC Bus from the drive HMI. 
In the monitor menu it will display "Mains Voltage". 
To calculate the DC Bus voltage: 
If you multiply this value by 1.414 (sq root of 2) the result will be the value of the DC bus. 
However, the drive does a calculation with the DC bus voltage to determine the mains voltage (line supply). 

Is there a way to determine the DC bus voltage from the display?

Issue:
How do you calculate the DC bus voltage using the "Mains Voltage" (ULn) displayed in the Monitor menu
 
Product Line:
ATV61, ATV71, ATV312, ATV12, ATV32
 
Environment:
All models and serial numbers
 
Cause:
None
 
Resolution:
The drive does a calculation using the DC bus voltage to determine the mains voltage (line supply).  The drive measures the DC Bus internally and multiplies it times 1.414 (square root of 2) and then displays it as the Mains Voltage (ULn) In the monitor menu.

How to do scaling in LXM32?

To set scaling, you need to set scale numerator and denominator in SoMove or these parameters can be written through CAN.
By default, as you can see in the screenshot from SoMove, 1 revolution corresponds to 16384 (resolution of encoder) user units. So, for example, if one revolution correspond to 100 mm, than ScalePOSdenom has to be set to 100. Similar for velocity and ramp (acceleration).

What type of hubs are used with the MP43200 Meter-Pak?

Product Line:
MP Meter-Pak

Environment:
Metering

Cause:
Need hub to bring conduit into an MP Meter-Pak

Resolution:
This Meter-Pak's utility compartment will accept two A-L type hubs (2" through 4") in the top endwall. Two closing plates, part number ACPL, are factory installed on the top endwall so the Meter-Pak can also be used for a bottom cable entry application. The bottom endwall will also accept two A-L type hubs (2" through 4"). The catalog numbers of the Series 'A-L' hubs are as follows;

2.0 inch - A200L
2.5 inch - A250L
3.0 inch - A300L
3.5 inch - A350L
4.0 inch - A400L 

Is there a junction box with minimum internal dimensions of 110mm(L) X 80mm(W) X 50mm(H) that also has a certain degree of weather protection available?

Yes the 265/4 would be suitable for the application. It is slightly larger however, it will meet the desired requirements.
Some of its key features are:
  • Surface mount
  • Dimension: 108 mm Length x 108 mm Width x 76 mm Height
  • 143.7 mm screw centres C, 89 mm screw centres D
  • Weatherproof, full cover plate
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=265/4


Is the input voltage of the drive (ULN) a true value or is it just calculated?

All Altivars uses the same method  to measure the mains voltage.

Input voltage of the drive ULN is calculated according to the DC bus voltage to determine the mains voltage (line supply).
In the monitor menu it will display "Mains Voltage". If you multiply this value by 1.414 (sq root of 2) the result will be the value of the DC bus
The accuracy depends of the type of application (motor mode or generator mode, with or without load).
According to the situation
-    Optimal accuracy when no load, or no motor current is <5%.
-    When load apply on motor accuracy is around 10-15%.
In generator mode: Information is not significant because DCbus value increase
 

Before importing a backup from a StruxureWare Data Center Expert server to the Virtual Appliance version, configure the public and private network settings first in VMWare.

Issue:
Before importing a backup from a StruxureWare DCE server to the Virtual Appliance version, configure the public and private network settings first in VMWare

Product Line:
StruxureWare Data Center Expert

Environment:
StruxureWare Data Center Expert Virtual Machine.

Cause:
Restoring a backup from a server with the public and private NICs configured to a VM that is configured with a single NIC can cause issues with the network mask settings on the VM. The restore of the backup will try to restore the configuration of the second NIC but will not do so correctly as there is no secondary NIC configured

Resolution:
To avoid this issue, please set up the second NIC's configuration on your StruxureWare Central Virtual Appliance before restoring the backup.

If you've already encountered this issue, you must go to the StruxureWare Central client and configure a different netmask. The netmask may look correct in the Central client but devices on the private network will not receive the correct netmask settings. Apply the change (the server will reboot). Log back into the StruxureWare Central client and then re set the correct network settings
 

Symmetra Power Array Input Voltage Selector Theory of Operation

Issue:
This document describes how the input voltage selector block of the Symmetra Power Array (NAM) works.

Product Line:
Symmetra Power Array

Environment:
NAM models only

Cause:
This document describes how the input voltage selector block of the Symmetra Power Array (NAM) works.  This is useful for understanding the theory of operation or for troubleshooting.

Resolution:
The input voltage selector switch is primarily responsible for two things:  routing power through the appropriate taps of the isolation transformer and notifying the intelligence modules of the expected input voltage. 

The reason that the IMs need to know the expected input voltage is so that the automatic bypass functionality can operate properly.  If the input differs drastically from the jumper setting, a bypass out of range message will be displayed and the UPS will not be capable of transferring to command or temporary bypass.

When the jumper is set to the up position, it makes contact with the microswitch at the top of the block.  This will notify the IMs to expect 240 VAC and will also jump the bypass source to the 240 VAC tap. 

When the jumper is not set (down position), the microswitch is open and the IM assumes 208 VAC input.  This also jumps the bypass to source to the 208 VAC tap. 

When on inverter, the power modules will output 240 VAC all the time and therefore the inverter output only needs to connect to the 240 VAC tap of the transformer.  The setting of the jumper is only necessary to obtain correct voltages while in bypass. If the jumper is not set correctly, the user will only realize it when in temporary, command, or manual bypass.


  

 

What could cause the DC bus voltage on a drive to drop when the motor is heavily loaded?

Issue:
What could cause the DC bus voltage on a drive to drop when the motor is heavily loaded?

Product Line:
All Variable Frequency Drives.

Environment:
All models, All serial numbers.

Cause:
As the speed of the motor increases, and/or as the load on the motor increases, the DC bus voltage is dropping and the motor current is increasing, while the main input voltage stays the same or drops very slightly.

Resolution:
There are multiple possible causes for this situation, but one that should be ruled out first is "flat topping" of the incoming power. The DC bus capacitor bank in the drive is charged to the peak to peak voltage of the incoming AC mains power.  To determine what the DC bus voltage should be, multiply the incoming AC voltage as measured by an RMS meter by the square root of 2.  Approximately 1.414 X the input RMS voltage.  As an example, if you read 480V AC incoming voltage RMS, the peak to peak AC voltage would be 678.8.   The DC bus would be charged to 480 X the square root of 2, or 678.8VDC

When you measure the incoming voltage with a voltmeter, you are measuring the RMS voltage.  So the DC voltage on the DC bus will be 1.414 X the RMS reading of your incoming AC voltage.  If your incoming power is overloaded slightly, your peak to peak incoming voltage will dip slightly.   This will have a very small change on your RMS meter reading, but a more significant change on the DC bus voltage.   As the DC bus voltage drops, the motor current will increase to maintain the same power at the motor.  If you were to look at your incoming power to the drive with an oscilloscope, you would see the top of the waveform would be flattened slightly.  This is an indication that your incoming power is being overloaded.  Steps should be taken to increase the amount of power available on your incoming power to the drive.

Is there a C clip for 13mm gyprock as the 154 doesn't fit ?

No, The 154 is designed to suit  up to 12mm and then the 154/1 suits from 19-25mm . If These are not suitable then 155 series may be used

What is basic troubleshooting procedures for NLP on an ATV61 or ATV71 drive?

Issue:
What can I do to resolve NLP on the display of my ATV71 or ATV61 drive?

Product Line:
ATV61 ATV71

Environment:
All

Cause:
Drive will not run.

Resolution:
WARNING: the person performing these tests will be exposed to AC Voltage up to 690 VAC and DC voltages up to 1000 VDC.  This should only be performed by a properly trained person while wearing appropriate PPE.  Consult the Product Installation Manual for details before attempting.

Check Line voltage phase to phase on the drive terminals.
Verify if the jumper is connected between PA (+) and PO terminals.  Larger HP drives may have a DC Choke connected between these terminals.
Check the DC bus voltage between PA (+) and PC (-)
Check the DC bus voltage between PO and PC (-)
Go to monitoring 1.2  (Drive Menu) verify mains voltage equals line voltage. 

DC Bus Voltage should be approximately 1.414 times the Line Voltage.
If voltage measurement from PA to PC is not correct, the input bridge of the VFD and the input line power will need to be tested.
If the Voltage measurement between PO and PC does not match the voltage measured between PA and PC there is an open or loose connection with the Jumper or DC Choke.
If the Voltage measurements are correct but the Mains Voltage displayed in the monitoring menu does not match, there may be a loose connection inside the VFD.  This can also be caused by distortion of the input line power called Flat topping.
If the Mains Voltage displayed in the monitoring menu shows "No Measure" power down the drive and verify the ribbon cable connection to the main control board of the drive.  This cable will connect to the Power Board on smaller HP drives and to the Motor Control Board on large HP units.

US customers can contact DPSG (Drive Products Support Group) for further assistance at 888-778-2733, option 2 for Technical Support and then option 4 for AC Drives and Softstarts.
Customers in other countries should contact their local Schneider Electric support.

 

What is the replacement for the 18464?

Part # 18464 - C120 - circuit breaker - C120H - 3P - 32A - C curve Has been discontinued and there is no direct replacement.

Customer can go for Part # 18727 - 3 Poles 32 Amps C Curve NG125H Breaker but it won't fit the same chassis.

https://www.schneider-electric.com.au/en/search/18727

ACRP1XX, ACRD5XX, ACRP5XX, and ACRC5XX Parts List

Issue:
ACRP1XX, ACRD5XX, ACRP5XX, and ACRC5XX Parts List.

Product line:
ACRP1Xx, ACRP5XX, ACRD5XX, ACRC5XX.

Environment:
All Serial Numbers.

Cause: 
Parts.

Resolution:
Please contact Cooling Tech Support to confirm the part numbers before quoting as some may have changed. 888-695-6500 Option 2, Option 2, Option 2
 
Description Part Number Mfg. P/N
     
ACTUATOR - FLOATING 132 IN-LBS W491-0521  
ADPTR ELBOW 1/2 INCH - 15 MM PEX (FOR PIPING - Compression coupling) [PART OF SHIP LOOSE KIT] W875-0989  
ADPTR PIPE 3" ENGL TO METRIC (adapter for connecting to metric pipe) 0M-61194  
ADPTR STRAIGHT 1/2 INCH - 1/2 INCH PEX (Humid & Cond Connections) [PART OF SHIP LOOSE KIT] W875-0991  
ADPTR STRAIGHT 1/2 INCH - 15 MM PEX [PART OF SHIP LOOSE KIT] 875-0989  
ATS - ACRP500 W451-0227  
ATS - ACRP501 W451-0226  
ATS TRANSFORMERS W430-0423  
BALL VALVE, GAS SHUTOFF 3/4" [PART OF SHIP LOOSE KIT] 875-4280  
CABLE ASSY 200V CONTROL JUMPER W0W3109  
CABLE ASSY ACRP CW MAIN CTRL W0W4760  
CABLE ASSY ATS CONTROL - ACRP5xx 208V (CW) (connects TIMERs, CONTACTORs, & CIRCUIT BREAKERs) 0W3103  
CABLE ASSY ATS CONTROL - ACRP5xx 480V  (CW) (connects TIMERs, CONTACTORs, & CIRCUIT BREAKERs) 0W3175  
CABLE ASSY CABLE ATS #1 200-240V 0W3121  
CABLE ASSY CABLE ATS #1 480V 0W3122  
CABLE ASSY FAN GUARD [female to female connector and the rear of the fan grill module] 0W3104  
CABLE ASSY FAN/HTR INTRLK ADAPT - ACRP1xx (DX) (P30A to P5 & P6) 0W3569  
CABLE ASSY FAN/HTR INTRLK ADAPT - ACRP5xx (CW) (P30A to P5 & P6) 0W3568  
CABLE ASSY Humidity Sensor For ACRP 1.6 ft - Spare Part (front) W0N-0297  
CABLE ASSY Humidity Sensor For ACRP 17ft - Spare Part (rear) W0N-0865  
CABLE ASSY TEMPERATURE SENSOR KIT (AT0056GB01 - ACRP ADDITIONAL SUPPLY TEMPERATURE SENSOR) 0N-0933  
CABLE ASSY THERMISTOR/PROBE EMU 1.6 FT (front) 0W3314A  
CABLE ASSY THERMISTOR/PROBE EMU 13 FT (RACK INLET) [PART OF SHIP LOOSE KIT] 0J-0W99952  
CABLE ASSY THERMISTOR/PROBE EMU 8 FT - SPARE PART 0J-0W3163A  
CABLE ASSY THERMISTOR/PROBE EMU 8 FT ASSY (Generic EMU sensor) AP9335T  
Cable Fan To Safety Plug for ACRPxxx (CW AND DX) - Spare Part W0W3105  
Cable for FAN ACRP1xx (DX) - Spare Part (P30 to P101/P100) W0W3118  
Cable For FAN ACRP5xx (CW) - Spare Part W0W3120  
Cable for Reheat ACRP1xx (DX) - Spare Part W0W3117  
Cable for Reheat ACRP5xx (CW) - Spare Part W0W3119  
Cable from Ckt Brk to Reheat/Humidifier for ACRP1xx (DX) - Spare Part W0W3106  
Cable from Ckt Brk to Reheat/Humidifier for ACRP5xx (CW) - Spare Part W0W3107  
Cable Main Power 208/400V For ACRP100/102 (DX) - Spare Part W0W3128  
Cable Main Power 480V For ACRP101 (DX) - Spare Part W0W3127  
Cable Main Power ACRP5xx ASSY ATS 200-240V #2 0W3125  
Cable Main Power ACRP5xx ASSY ATS 400-480V #2 0W3126  
CABLE TIE HNGD FOR HOLE D4.8MM ROHS [PART OF SHIP LOOSE KIT] 820-0048  
CABLE Variable Frequency Drive 200V for ACRP100 (DX) - Spare Part W0W3171  
CABLE Variable Frequency Drive 400V for ACRP101 (DX) - Spare Part W0W3116  
CDU Metric Pipe Connection Kit ACAC20012  
Circuit Board For Compact ACRP100/500 208 VAC 3 Phase - Spare Part (Humid Control Board) W0P2484  
Circuit Board For Compact ACRP101/501 460 VAC 3 Phase - Spare Part (Humid Control Board) W0P2505  
Circuit Breaker 2P 5A 240V Class K -  ACRP500 ATS MONITOR BREAKERS W530-0920 ABB P/N : 2CDS 272 417 R0357
Circuit Breaker 2P 5A 480V UL489 Class K - ACRP501 ATS MONITOR BREAKERS W530-0919 ABB P/N : 2CDS 272 317 R0357
Circuit Breaker 3P 10A 280V Class K -ACRP500/100 HUMIDIFIER BREAKER W530-0917 ABB P/N :  2CDS 273 417 R0457
Circuit Breaker 3P 10A 480V UL489 Class K - ACRP101 ELECTRIC HEATER BREAKER W530-0918 ABB P/N : 2CDS 273 317 R0427
Circuit Breaker 3P 15A 480V UL489 Class K - ACRP501 ELECTRIC HEATER BREAKER W530-0916 ABB P/N : 2CDS 273 317 R0457
Circuit Breaker 3P 20A 240V UL489 Class K -ACRP100 ELECTRIC HEATER BREAKER W530-0915 ABB P/N : 2CDS 273 417 R0487
Circuit Breaker 3P 30A 240V Class K - ACRP500 ELECTRIC HEATER BREAKER W530-0913 ABB P/N : 2CDS 273 417 R0527
Circuit Breaker 3P 30A 480V - ACRP501/101 CB0-A/B INPUT BREAKER W530-0442 ABB P/N : T1N030TL
Circuit Breaker 3P 50A 480V - ACRP501/101 CB0-A/B INPUT BREAKER W530-0445 ABB P/N : T1N050TL
Circuit Breaker 3P 50A 280V TMF ABB T1N -ACRP500 CB0-A/B INPUT BREAKER W530-0445 ABB P/N : T1N050TL
Circuit Breaker 3P 5A 240V Class K - ACRP500/100 FAN / COND PUMP W530-0912 ABB P/N : 2CDS 273 417 R0357
Circuit Breaker 3P 5A 480V Class K - ACRP501/101 FAN / COND PUMP W530-0911 ABB P/N : 2CDS 273 317 R0357
Circuit Breaker 3P 70A 280V TMF ABB T1N - ACRP100 CB0-A INPUT BREAKER W530-0447 ABB P/N : T1N070TL
Circuit Breaker 3P 8A 480V UL489 Class K - ACRP501/101 HUMIDIFIER BREAKER W530-0909 ABB P/N : 2CDS 273 317 R0407
CLAMP DOUBLE SNAP CRIP 27-31MM [PART OF SHIP LOOSE KIT] 875-00009  
Complete 801 PCB CRAC MB - (MB Only) W0P2340  
Complete 805 PCB CRAC 2X DP - (DPS Diff Pressure Card) W0P2354  
Complete 879 PCB XA SIMM - (XAS card) W0P2342  
COMPRESSOR 200V RECIP N-VAR R407C (ACRP100) 208v W875-3801 120B0032
COMPRESSOR 460V RECIP N-VAR R407C (ACRP101/ACRP102) 460v W875-3802 120B0004
COMPRESSOR NOISE COVER (MEETS UL 94 HB) 850-0665A  
Condensate Overflow CLAMP DOUBLE SNAP CRIP 27-31MM 875-00009  
Condensate Overflow HOSE STEAM SUPPLY 7/8ID 660-7002B  
Contactor A26 Coil 200/240VAC 1NO For ACRP500 - Spare Part W451-0046 ABB P/N : 1SBL241001R7510
Contactor, NR 24VAC 16 AMP 1NO - Spare Part (ACRP100 - heater) W451-0141 ABB P/N : A16-30-10-81
Contactor, NR 24VAC 9 AMP 1NO - Spare Part (ACRP101 - both heaters & humidifier; ACRP100 - humidifier) W451-0104 ABB P/N : A9-30-10-81
CPLR HFC35 PIPE THREAD SHUTOFF 3/8 BSPT [PART OF SHIP LOOSE KIT] 875-0978  
CPLR PLC PIPE THREAD SHUTOFF 3/8 BSPT [PART OF SHIP LOOSE KIT] 875-0974  
CRANK CASE HEATER ASSY #1 W0M-9895  
ELBOW ADPTR REDUCTION 1/2 INCH - 3/8 INCH [PART OF SHIP LOOSE KIT] 875-0990  
Fan Module Assembly 200V - Spare Part W0M-9841  
Fan Module Assembly 400-480V ACRP101/501- Spare Part W0M-9848  
FILTER AIR 30% 418X470X96 MM (Standard) 0J-875-2013A  This is a pack of 4 filters
FILTER AIR 85% 418X470X96 MM  (Optional) W875-2014  
Flexible Fluid Piping - 100 Feet (30.4 Meters) ACAC20003  
Flexible Fluid Piping - 300 Feet (91.4 Meters) ACAC20002  
Flexible Fluid Piping Clamp/Hanger ACAC20007  
Flexible Fluid Piping Clamp/Hanger (qty of 50) ACAC20008  
Flexible Fluid Piping Couplings (4 per pack) [875-4308 is the individual pn#] ACAC20006  
Flexible Fluid Piping Couplings FTG PEX 1"NPT with CRIMP [comes in a pack of 4 with pn#ACAC20006] 875-4308  
Flexible Fluid Piping Insulation - 100 Feet (30.4 Meters) ACAC20005  
Flexible Fluid Piping Insulation - 300 Feet (91.4 Meters) ACAC20004  
Flexible Fluid Piping Strut Mounted Clamp ACAC20009  
FLOW METER - 1"  (body of the flowmeter) W875-4018  
FLOW METER ELECTRONIC PIPING FLOW electronics section of flowmeter W0N-0278  
FLOW METER GRUNFOS (new flowmeter) W0N-0303  
Flow meter UNION 1.0" C X NPTI (* send 2 with a flow meter body) 875-0876  
FLTR-DRIER 5/8" ODF SOLDER W875-2012  
FUSE FAST 30A CLASS J 600V CUBEFUSE for Compressor - ACRP101 (DX 400V) W516-0107 BUSSMANN : TCF30
FUSE FAST 60A CLASS J 600V CUBEFUSE for Compressor - ACRP100 (DX 200V) W516-0106 BUSSMANN : TCF60
FUSEHOLDER CLASS J 30-60A 600V CUBEFUSE - ACRP1xx (DX 200/400V) W890-0079 U2-1IGZ/H U2311301
GASKET FOR INROW CW 3-WAY VALVE W875-00012  
HIGH PRESSURE SWITCH ASSY (cuts out at 377psi) W0M-9897  
HOSE STEAM SUPPLY 7/8ID (ordered in feet) [PART OF SHIP LOOSE KIT] 660-7002B  
HUMIDIFIER COMPACT 1-3 KG/H 200 V (humidifier frame) 875-9001  
HUMIDIFIER COMPACT 1-3 KG/H 480 V (humidifier frame) 875-9003  
HUMIDIFIER CYLINDER HOLDING BELT W875-00029  
HUMIDIFIER DRAIN VALVE SLND CAREL 1-1/4 IN W875-4257  
HUMIDIFIER FILL VALVE W875-4233  
HUMIDIFIER HIGH COND. CYLINDER REPLA 1-3KG/H 208V (Standard conductivity 350-1250) W491-0529 BL0TRB00H1
HUMIDIFIER HIGH COND. CYLINDER REPLA 1-3KG/H 480V (Standard conductivity 350-1250) W491-0528 BL0TRM00H1
HUMIDIFIER LOW COND. CYLINDER REPLA 1-3KG/H 208V SPARE PART (Optional conductivity 125-350) W875-00030 BL0TRA00H1
HUMIDIFIER LOW COND. CYLINDER REPLA 1-3KG/H 480V SPARE PART (Optional conductivity 125-350) W875-00032 BL0TRL00H1
HUMIDIFIER Printed Circuit Board For Compact 3 KG/H 400 VAC 3-Phase - Spare Part W0P2504  
HUMIDIFIER Printed Circuit Board For Compact 3 KG/H 208 VAC 3-Phase - Spare Part W0P2484  
KIT DOOR CRV POWERVIEW 42U 600MM SX (BLK KEY) (Rack) W0H-0128  
KIT DOORS SPLIT PERF 42U 600MM BLK SX (Rack) W0H-0042  
LABEL MODEL/ SERIAL # ROHS [PART OF SHIP LOOSE KIT] 885-7015B  
Leak sensor (ships with orange sensor and cable ties; NO BLACK CAT5e CABLE)[ACRP ONLY] AP9326  
Main Control Cable for ACRP1xx (DX) - Spare Part W0W3100  
Main Control Cable for ACRP5xx (CW) - Spare Part (new flow meter) W0W4760 (old flow meter) W0W3101  
MOTHERBOARD SET (MB,WC,XA,DP,OPT)  (Complete Board Assy) W0P2372  
Motherboard Set 1-Bay Board Set (MB,WC,XA,DP,OPT,485-FMTR) - Spare Part (board set for new flowmeter) W0P2860  
NMC with CAN controller - (EMBEDDED NMC) WAP9517CAN  
PCB 808 CRAC 9X RLY 2X OPTO FAN TACH (relay board) W0P2465  
PCB 811 CRAC 8X OPTO SIMM (SIMM Card power control board) W0P2358  
PCB CMS Complete 809 CRAC 3X RS485 SIMM - (CMS power control board) W0P2355  
PCB COMMUNICATION CARD FOR RS485 (Humid Comm Board) W0P2483  
Peristolic Pump (Pump only) 491-0510  
Peristolic Pump Goo (solution-send with the perostolic pump) 491-0511  
PIPE ASSY 6 INLET RECIVER 0M-9815A  
POLY BAG (6" X 9") PA130 [PART OF SHIP LOOSE KIT] 872-9014  
POWERVIEW MP - SPARE PART W0N-0286  
PRESSURE RELIEF VALVE -3/8 MPTX1/2 FLARE 425PSIG (INDOOR) W875-4230  
PUMP CONDENSATE HARTELL 240V * ALL UNITS 200/400/480 W491-0523  
QUICK CPLR HFC35 ELBOW HOSE SHUTOFF 1/2 ID (Internal Connections Condensate to W875-0979) W875-0981  
QUICK CPLR HFC35 HOSE SHUTOFF 1/2 ID (Internal Connections Condensate to W875-0981) W875-0979
QUICK CPLR HFC35 IN-LINE HOSE SHUTOFF 1/2 ID (Condensate Connects to W875-0978) W875-0980
QUICK CPLR HFC35 PIPE THREAD SHUTOFF 3/8 BSPT (Condensate Connects to W875-0980) [PART OF SHIP LOOSE KIT] W875-0978
QUICK CPLR PLC ELBOW MALE 3/8 OD 1/4 ID (Internal Connections Humid to W875-00020) W875-00021
QUICK CPLR PLC PIPE THREAD SHUTOFF 3/8 BSPT (Humid Connects to W875-0976) [PART OF SHIP LOOSE KIT] W875-0974
QUICK CPLR PLC PNL MNT FEMALE 3/8 OD 1/4 ID  (Internal Connections Humid to W875-00021) W875-00020  
QUICK CPLR PLC PNL MNT HOSE SHUTOFF 3/8 OD 1/4 ID (Humid Connects to W875-0974 ) W875-0976  
Reheat Module for 200V ACRP100/500 - Spare Part W0N-0813  
Reheat Module for 400-480V ACRP101/501- Spare Part W0N-0812  
RES CARB FILM 1/4W 5% 120 OHM [PART OF SHIP LOOSE KIT] 110-0121  
ROTO MALE STRAIGHT 1 1/4" - 3/4" SWT - (DX Refrig Supply and Return Connections Internal) 875-4285  
Rotolock Pipe FEMALE ENDCAP 1-1/4" 12 UNF W875-4288  
Rotolock Pipe Female Straight Fitting 1-1/4" - 3/4" SWT - (DX Supply & Return Connection) [PART OF SHIP LOOSE KIT] W875-4286  
SCREW M5 X 10MM TORX W/WASHERS ROHS [PART OF SHIP LOOSE KIT] 803-5531A  
SCREW M6 X 16MM TORX W/WASHERS ROHS [PART OF SHIP LOOSE KIT] 803-0686A  
SCREW M6X12MM TORX W/WASHERS ROHS [PART OF SHIP LOOSE KIT] 803-0684A  
SCREW THFM M6X10MM PN HD TX ZP [PART OF SHIP LOOSE KIT] 803-0660  
Side Panel Assy  42U x 1070mm Blk W0M-5965  
SIGHT GLASS 5/8" ODF SOLDER (Piping) W875-2011  
SOLENOID 24AC COIL 6POSITION PLUG ASSY  (BYPASS) W0M-8204  
SOLENOID COIL ASSY (LL) W0M-9894  
SOLENOID REFRIGERATION VALVE 3/8 875-4196  
SOLENOID REFRIGERATION VALVE 5/8 W875-4282  
STRAIGHT ADPTR REDUCTION 3/8 BSPT-1/2 NPT  (Humid & Cond Supply) 875-4341  
TEFLONRINGS FOR ROTO 1 1/4"  (for suction line at the compressor) [PART OF SHIP LOOSE KIT] W875-4294 compressor
TEFLONRINGS FOR ROTO 1" (for discharge line at the compressor) [PART OF SHIP LOOSE KIT] W875-4291  
TELECOUPLNG 8P8C RJ45 STRAIGHT (ethernet telecoupler) W750-0034  
TEV VALVE, 5/8 IN 7/8 OUT R-407C W875-1001  
TRANSDUCER PRESSURE 2CP5 W875-3400  
TRANSFORMER CLASS II 100VA 208-230-460-480VX24V-30V W430-0197 T30018 Rev C
TYRAP 390MM V0 RATED GT120RV0 [PART OF SHIP LOOSE KIT] 820-0390  
UNION - Ring Seal D35 X 3 - (CW Supply and Return Connections) W875-4298  
UNION 1.0" C X NPTI Gasket 875-0887  
UNION END 1-3/8 ID SWT CW 37 Sleeve Union End (CW Supply and Return Connections) 875-00014  
UNION END 1-3/8 ID SWT HEX (CW Return Connections) 875-00034  
UNION Extension Adapter COPLING 11 NPT 1-3/8 ID SWT (CW Supply and Return Connections) 875-00015  
UNION FITTING 1-1/2'' 11 NPT  (CW Supply and Return Connections) 875-4289  
UNION NOT 1-1/2'' 11 NPSM 1 3/8'' SWT (CW Supply Connections) 875-4292A  
VARIABLE FREQUENCY CONVERTER 11KW 200 V W491-0531  
VARIABLE FREQUENCY CONVERTER 11KW 400 V W491-0530  
VARIABLE FREQUENCY Electrical Board 11KW 200 V (1.07 upgrade) 530-1138A  
WIRE ASSY FM 208V JUMPER 0W2540  
WIRE ASSY FM 208V JUMPER SET W0H-0152  
WIRE ASSY FM 230V JUMPER 0W2541  
WIRE ASSY FM 380V JUMPER 0W2542  
WIRE ASSY FM 400V JUMPER 0W2543  
WIRE ASSY FM 415V JUMPER 0W2544  
WIRE ASSY FM 460V JUMPER [PART OF SHIP LOOSE KIT] 0W2545  
WIRE ASSY FM 480V JUMPER 0W2546  
WIRE CLIP - BLACK AP9335TH [PART OF SHIP LOOSE KIT] 870-13220  
Wire Kit Customer Interface (CW AND DX) - Spare Part W0W3124  
WIRE TIE 8 X 0.1 X 0.06 NYLON 105C ROHS [PART OF SHIP LOOSE KIT] 820-0003A  
ZIP LOCK POLY BAG 3 X 4 [PART OF SHIP LOOSE KIT] 872-0019  
1U Airflow Management Blanking Panel Kit (Qty 2) Black AR8108BLK   
1U 19" Black Modular Toolless Airflow Management Blanking Panel - Qty 10    AR8136BLK  
1U 19" Black Modular Toolless Airflow Management Blanking Panel - Qty 200    AR8136BLK200  
MECH-ELEC INTERLOCK FOR CONT. A9-A40 450-0515  
 
 
 
RC/RP50x CW Supply Piping                                 RC/RP50x CW Return Piping                    RD50x/RP10x DX Supply & Return Piping

 

 
HUMIDIFIER SUPPLY LINE                                         CONDENSATE DRAIN LINE