ELBOW COND PVC SOLID 16MM

There are 50 16mm saddles in a carton.

Note: This information can be found in your Clipsal pocketbook right next to the part code.

Yes, there is the 93ER and also the 249/12 or 249/25.

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

The 265 series is a range of IP56 rated insulated boxes suitable for numerous junctions and terminations. Each box is supplied with a 3mm sealing gasket.

This applies to the 265/1, 265/3, 265/4, 265/5, 265/7 and 265/7D.

 Combine a mccb 25016 32Amp C-curve with a 23382 rccb = RCBO

No it doesn't have a rating as such, however it is UV resistant.

The part number for the screws would be 265SCREW.

No, the 252/32/2A only comes in grey.

Yes, we can offer the 265/1 in electric orange. The part number is 265/1-EO.
Some of the key features are:

• Surface mount
• Dimension: 77 mm Length x 77 mm Width x 54 mm Height
• 63.5 mm screw centres C, 63.5 mm screw centres D
• Weatherproof, full cover plate

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=265/1


 

Part number "24541" was a 3 Poles 20 Amps D Curve 6 KA C60N Circuit Breaker which has been discontinued.

In the new series we have D curve Circuit Breakers available in 10 KA i.e. iC60H series.

The part number for the iC60H 3 Poles 20 Amps D Curve 10 KA Circuit Breaker is "A9F55320"

https://www.schneider-electric.com.au/en/search/A9F55320



 

Issue:

NetBotz History Export date is seen as a Linux Time Stamp.

Product Line:

NetBotz

Environment:

NetBotz History Export.

Cause:

NetBotz is based on the Linux operating system and as such much of it's data uses a Linux Time Stamp The Exported data may look something like this:
"Sensor Pod (integrated)";"Temperature";"1465097276057";"30.00"

Resolution:

It is unlikely this will be changed in a future revision so if it is necessary to view this as a date, the information can always be imported into a spread sheet application such as Microsoft Excel.

I can translate 1465097276057 on the epochtime.com page but in Microsoft Excel, the number does not translate easily. I must delete the last 3 digits just to be able to use the suggested Excel formulae:
=(((C2/60)/60)/24)+DATE(1970,1,1)<br />
or
=C2/(60*60*24)+"1/1/1970"

You can also cut off the rest of the numbers by using a formula like this:
=(((LEFT(C2,10)/60)/60)/24)+DATE(1970,1,1)
When formatted properly using a time format, the result should look like this:
6/5/16 3:27 AM
 

You will find all the characteristics of LC1Dxx contactors on the Tesys web page:
 
The section Downloads has documents ( Catalogues, Brochures, Catalogue pages, Tech publications, Certificates, etc...) that you can download free

See the following documents in the online catalogue: 24505; 24506 and 24533
(Use the search bar on the top right hand side of the web site to search for these particular documents)

Issue
Wire recommendation to use with EM4200 series meters

Product Line
EM4200 series meters
EM4235
EM4236

Environment
Meter wiring 

Resolution
The EM4200's recommended wire size for I/O, Communications, and CT is 24-16 AWG (0.2 to 1.5 mm²) shielded wire, solid or stranded.

Issue:   Can the ATV28 drive accept 4-20 mA analog input?
 
Product Line:   ATV28
 
Environment:  All
 
Cause:   N/A
 
Resolution:   Yes. It can be used as a summed reference, speed reference or PI regulator feedback. It can also be configured as a 0-20mA current loop. The input is located at terminal AIC.


 

Issue:
User wants to know where to install I/O modules on a PM8000 meter.
 
Product Line:
PM8000 meters
METSEPM89M2600 (Digital I/O module)
METSEPM89M0024 (Analog I/O module)

Environment:
I/O modules installation

Resolution:
*Warning:  Installation and maintenance of this device should only be performed by qualified, competent personnel that have appropriate training and experience with high voltage and current devices. Failure to follow the instructions / warnings in the Meter Installation Guide can result in permanent damage to the meter, severe injury or death.

There are 2 methods to install I/O modules on a PM8000 meter. The method to choose will depend on your PM8000 model number

If meter is PM8240 (Panel mount meter with integrated display)
I/O module to be installed on the back of the meter. 
1) remove connector's cover on back of the meter
2) Make sure that connectors on meter and I/O module align with each other. Attach I/O module to the back of the meter.
3) secure the I/O module in its location by a 5mm (5/16 in) screw
4) reattach connector's cover that was removed in step 1 to the back of I/O module
See illustration below:


If meter is either PM8243 or PM8244 (DIN rail mount meter)
I/O module to be installed on the side of the meter:
1) remove connector's cover from side of the meter
2) Hang the I/O module on your DIN rail
3) Secure I/O module to the DIN rail using Mounting clip.
4) Move I/O module using the DIN rail and attach it to the PM8000 meter> You should hear a click.
5) Secure the I/O module to the meter using a 5mm (5/16 in) screw.
6) reattach connector's cover that was removed in step 1 to the back of I/O module
See illustration below: