coupling cond pvc expansion

COUPLING COND PVC EXPANSION

Catalogue Number: 251/20
coupling cond pvc expansion
Colour: Grey
Colour: Per UOM Std.
  • Grey 1 PCE 1

Specifications

hide show
Product brand
Clipsal
Range of product
Series 251
Material
PVC (polyvinyl chloride)
Product destination
diameter: 20-20 mm tube
Length
63-76 mm
Standards
AS/NZS 2053
REACh Regulation
Free of Substances of Very High Concern above the threshold
REACh free of SVHC
Yes
EU RoHS Directive
Pro-active compliance (Product out of EU RoHS legal scope)
Toxic heavy metal free
Yes
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
 Pro-active China RoHS declaration (out of China RoHS legal scope)

Frequently Asked Questions

hide show

What are the part numbers of slip type expansion couplings?

Slip Type Expansion Couplings are available from 16mm through to 50mm.The part numbers of slip type expansion coupling are as follows:
16mm = 251/16
20mm = 251/20 *
25mm = 251/25 *
32mm = 251/32
40mm = 251/40 *
* = only available in Grey
Where long conduit runs are likely to be exposed to wide variations in temperature, it is recommended that expansion couplings be used at each join. It is not recommended that Slip Type Expansion Couplings be used where the conduit run is exposed to the weather. Standard colour is Grey (GY).
Dimension details are attached.
 

Can I get the 251/50 in orange?

No. Unfortunately, the 251/50 is the only one that comes in grey.

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=251/50



 

Do you have a cap/ flange to for 20mm conduit?

Yes the part number is 221/20

What would be a longer screw to suit Clipsals round j-boxes (Junction Boxes)?

The part number would be 248/20 which is a combination screw head 20MM 3/16 BSW.

Can I order the 220/20 in white?

Yes, you can order the 220/20 in white but it needs to be done as a special.
For more information, please refer to the link:https://www.clipsal.com/Trade/Products/ProductDetail?catno=220/20

What size Clipsal saddles are available?

Size       Ctn Qty     Part Code
16mm    50             261/16
20mm   100            261/20
25mm   100            261/25
32mm    50             261/32
40mm    50             261/40
50mm    20             261/50

Are the Clipsal Conduit Clips available in Electric Orange?

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

What is the part number for a 50mm female and 50mm male bush?

The part number for a 50mm female and 50mm male bush is - 281/50 & 281F50
For further information , visit link below:-
www.clipsal.com/Trade/search-results?q=281/50
https://www.clipsal.com/Trade/search-results?q=281F50
User-added image

 

Does Clipsal have a blank plate in the standard series, the same size as a 25/2?

Yes we do, it's the 31/2VX-WE.

What are the part numbers for the 25mm PVC saddles and spacers?

The part numbers are 261/25 for the saddles and 261S25 for the spacers. 

Some of the key features are:
  • 63mm Length x 20mm Width x 29mm Overall Height
  • 48mm Mounting Centre
For further information please visit https://www.clipsal.com/Trade/search-results?q=261/25



 

What is the part number for the bitsa box?

The part number for the bitsa box is 357TB.
Some of the key features are:
  • Tool boxes
  • 12 compartment transparent box with assorted screws, screws and quantities included
  • Includes: 357WF30 (100), 357/20 (150), 357WH12 (350), 357P30 (200), 357P20 (300), 357WH25 (100), 357PH50 (50), 357/63 (50), 357WHP32 (100), 357PH45 (100), 357/35 (100), 357/40 (100)
For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=357TB


 

What is part number for mounting clip to suit 25/2V?

The part number for mounting clip is a 154/2.

Where are the 1 N/O and 1 N/C auxiliary contacts located on the LC1D Contactors?

They are on the front of the contactor with the coil connections, terminal 13/14 for NO and 21/22 for NC

 

Will 25/2V double outlet, large size, vertical fit on 155P2 plaster bracket?

Yes, 25/2V will fit on 155P2. 25/2V is  Large Size Format 115 x 115mm, Double Power Outlet rated to 250V 10A.
For further information please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=25/2V
User-added image

155P2 is a large plaster mounting bracket with 84mm mounting centre. For further information please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=155P2
User-added image
 

What are the dimensions for a 261S Saddle Spacer?

The dimensions for a 261S Saddle Spacer are 261S are:
 
Saddle Spacers
Catalogue Number Size Length (L) Width (W) Centres (CRS.) Standoff (T) Height (H)
261S16 16mm 55mm 21mm 32mm 8mm 14mm
261S20 20mm 61mm 22mm 40mm 8mm 14mm
261S25 25mm 74mm 26mm 48mm 8mm 14mm

Saddles Spacers set a conduit run off the wall 8mm to allow easier cleaning and repainting and to facilitate entry into equipment. They are available in sizes 16mm through 25mm.
Standard colour is Grey (GY), with Orange (EO) also available at extra cost.

For further information please visit www.clipsal.com/Trade/search-results?q=261S


 

What is the part number of the mounting block to suit 25/2V Standard range, double socket outlet, large size format 115 x 115mm?

448SD and 448 are the mounting blocks to suit 25/2V, Standard range, double socket outlet, large size format 115 x 115mm.  Dimensions of the mounting block are as follows:

For further information , please visit
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448SD
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448
448SD
User-added image
448
User-added image
 

Using Modbus to trigger a Waveform Capture on a CM2000

Product Line
CM2000 series meter

Environment
Modbus Register Writes

Resolution
In order to trigger a waveform capture, it will be necessary to use Modbus Command Writes to trigger the waveform capture.

Using Modbus Tester (or another Modbus read/write program):

Write the value 4913 to register 7700.
Write the value 1 to register 7701.
Write the value 28120 to register 7702.

How to calculate Energy readings from the raw Integer register data on an Energy Meter

Issue
The energy values are stored across two 16-bit integer registers on an energy meter. 

Product Line
Energy Meter

Environment
Reading and converting Modbus register values

Resolution
The Energy Meter stores energy across two 16-bit integer registers.

Register #1 and Register #2 (Modbus address 257/258 for Register #1 and 259/260 for Register #2). Register #2 is the High WORD and Register #1 is the Low WORD. 

The Multiplier/Divisor table states that both of these registers must be divided by 32 to obtain the real value from the raw data.
The Multiplier/Divisor should NOT be applied to both registers. It is applied to the final value of both registers.

To calculate the Energy the registers must first be arranged as the register list states [2] is the High word and [1] is the Low word.

To make [2] the High word it needs to be shifted to the left 16 bits.
To accomplish this multiply the value in [2] by 65,356.
You will then add this value to the value in [1].
The final value will be divided or multiplied by the correct scaling value. Please see the example listed below.

For this example we will assume an Energy Meter with 300 amp CTs. According to the Integer Multiplier/ Divisor table, 300 amp CTs will give a divisor value, (d), of 32 and a multiplier value, (m), of 0.03125.
We will assume the following register values.
Register #1 = 29,586
Register #2 = 31

Using Divisor Table
kWh = ([R2]*65,536+[R1])/d
kWh = (31*65,536+29,586) / 32
kWh = 64412.56

Using Multiplier Table
kWh = ([R2]*65,536+[R1]) * m
kWh = (31*65,536+29,586) * 0.03125
kWh = 64412.56

*Note the divisor will not always be 32 and the multiplier will not always be 0.03125. For the correct values please see the Integer Multiplier Table.
 

What are the pinouts for current inputs on the AMI0810 when using the FTW308 cable with pigtail leads ?

 

 

 
  : Here are the pin assignments for current inputs I0 - I7 when using the FTW308 cable and the BMXAMI0810 .
 
      
    Current input 0  +                   pins 1/3 blue/white & white/blue are jumped together
    Current input 0  common        pin 2 white/orange
 
    Current input 1  +                   pins 4/6  green/ white & white/green are jumped together
    Current input 1  common        pin 5 orange/white
 
    Current input 2  +                   pins 7/9 white/brown  & brown/white are jumped together
    Current input 2  common        pin 8   white/gray 
 
    Current input 3  +                   pins 10/12 blue/red & red/blue are jumped together
    Current input 3  common        pin 11 gray/white
 
    Current input 4  +                   pins 15 /17 red/ orange & orange/ red are jumped together
    Current input 4  common        pin 16 red/green
 
    Current input 5  +                   pins 18/20 brown/red & red/brown are jumped together
    Current input 5  common        pin 19 green/red  
 
   Current input 6  +                 pins 21/23 red/gray & gray/ red are jumped together
   Current input 6  common        pin 22 black/blue
 
   Current input 7  +                   pins 24/26 black/orange & orange/ black are jumped together
   Current input 7  common        pin 25 blue/black 


R-6-30-17

Legacy KB System (APS) Data: RESL211859 V1.0, Originally authored by DaSo on 06/21/2013, Last Edited by DaSo on 06/21/2013
Related ranges: Modicon M340

What are the Commercial and Government Entity (CAGE) codes for Schneider Electric (US only)?

The CAGE codes for Schneider Electric/SQUARE D are listed below:
CAGE Code Company Address
04429 SQUARE D CO LEEDS MFG PLANT 940 MOORE ST NE LEEDS, AL 35094
05684 SQUARE D CO MIDDLETOWN MFG PLANT 1500 S UNIVERSITY BLVD MIDDLETOWN, OH 45044
07442 SQUARE D CO DALLAS ASSEMBLY PLANT 1111 REGAL ROW DALLAS, TX 7524
12670 SQUARE D COELECTROMAGNETIC INDUSTRIES DIV 1410 DONALDSON PIKE B-5 NASHVILLE, TN 37217
14280 SQUARE D CO LEXINGTON MFG PLANT 1601 MERCER RD LEXINGTON, KY 40511
14799 SQUARE D CO CHICAGO ASSEMBLY PLANT 9522 W WINONA SCHILLER PARK, IL 60176
19804 SQUARE D CO GRAND BAY OF BRECKSVILLE 6995 S EDGERTON RD SUITE 100 BRECKSVILLE, OH 44141
2E203 SQUARE D CO 810 GLEN EAGLE CT SUITE 100 BALTIMORE, MD 21286
4T466 SQUARE D CO 1010 AIRPARK CENTER DR NASHVILLE, TN 37217
51917 SQUARE D CO ASHEVILLE MFG PLANT 128 BINGHAM RD ASHEVILLE, NC 28806
51918 SQUARE D CO AUTOMATION AND CONTROL BUSINESS RALEIGH, NC 27611
51920 SQUARE D CO COLUMBIA MFG PLANT SUMTER HWY 76 AND 378 COLUMBIA, SC 29209
55947 SQUARE D CO SORGEL MFG PLANT 4065 N RICHARDS ST MILWAUKEE, WI 53212
56158 SQUARE D CO OSHKOSH MFG PLANT 3300 MEDALIST DR OSHKOSH, WI 54901
56302 SQUARE D CO CEDAR RAPIDS MFG PLANT 3700 6TH ST SW CEDAR RAPIDS, IA 52406
56303 SQUARE D CO 1717 CENTER PARK RD LINCOLN, NE 68512
56304 SQUARE D CO OXFORD MFG PLANT 5735 COLLEGE CORNER RD OXFORD, OH 45056
56365 SQUARE D CO CORPORATE OFFICES 1415 S ROSELLE RD PALATINE, IL 60067
63637 SQUARE D CO MISSOURI MFG PLANT 4800 PARIS RD COLUMBIA, MO 65202
63831 SQUARE D CO HUNTINGTON PLANT 6 COMMERCIAL RD HUNTINGTON, IN 46750
70745 SQUARE D CO SENECA PLANT 1990 SANDIFER BLVD SENECA, SC 29678
88434 SQUARE D CO 13191 CROSSROADS PKY N SUITE 205 LA PUENTE, CA 91746
88753 SQUARE D CO 3516 CONCORD RD YORK, PA 17402


Legacy KB System (APS) Data: RESL206488 V1.0, Originally authored by MaTh on 10/26/2011, Last Edited by MaTh on 10/26/2011
Related ranges: Standards Applied to Power Management PRODUCTS

Changing the Language of the Symmetra PowerView RM Display


Issue

I need to change the language displayed by my PowerView RM display interface


Product Line

Symmetra Power Array
Symmetra RM
Symmetra LX
Symmetra PX
Smart-UPS VT
Smart-UPS RT 15/20 kVA
PowerView display interface


Environment

All serial ranges


Cause

The display defaults to using the English language.  The user may opt to display the information in a different language.


Resolution

You can change the language by downloading new firmware into the PowerView RM interface. French, German, Italian, and Spanish are available on the enclosed CD. Support for additional languages may be available on the CD or at the APC Web site (https://www.apc.com). Product documentation in these languages also appears on the CD or at the APC Web site.  To change the language of the interface, perform the following steps in the order given.


1. Disconnect the PowerView RM from the UPS.

2. Disconnect the data cable from the RJ-45 port of the PowerView RM.

3. Connect the programming cable (included, APC part number 940-0082) between PowerView RM and the UPS data cable:
a. Attach the RJ-45 connector to the port on the rear of the PowerView RM interface.
b. Connect the female DB-9 connector of the programming cable to a serial port on the computer. The downloading computer must have access either to the file on the CD provided with PowerView RM or to the APC Web site.
c. Attach the UPS data cable to the female RJ-45 connector on the programming cable.

4. Locate the language program file to be downloaded into PowerView RM. Each language program file appears on the CD under the folder of its language(Français, Español, etc.) with a .bin extension. Program files for additional language support or code updates may be available on the APC Web site.

5. Place the PowerView interface in programming mode by pressing simultaneously the three keys on the right (Escape, Help, and Enter) for about three seconds, until the interface emits a long beep. The LCD will display the Programming screen. To leave the Programming screen before starting a file transfer (step 6), press Esc until it beeps (about one second).

6. Start HyperTerminal or another terminal emulation program on the computer. Set the communication parameters to 8 bits, no parity, no flow control, 1 stop bit, and 19,200 bps. After establishing a connection, use the Xmodem protocol to transfer the language program file from the CD or your download folder to PowerView RM. When the file transfer is complete, the PowerView RM interface will reset itself and display the Startup screen in the new language. If the file transfer fails, the interface will reset itself. Retry the file transfer by repeating steps 5 and 6.

7. Quit the terminal session. Disconnect the programming cable and reconnect the UPS data cable to the PowerView RM RJ-45 port.

8. Affix the PowerView RM to the UPS.
 

Which wall box suits the large size, twin socket outlet 25/2V?

The wall box that suits the large size, twin socket outlet 25/2V is 257D2-GY.
Its key features are:
  • 2 gang
  • 84 mm x 46 mm mounting center
  • Suits universal wall construction
  • With 20 mm cut-outs one end and 25 mm cut-outs at other, impact resistant, deep-type
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=257D2