TERMINATOR STRAIGHT 16MM

There are 50 16mm saddles in a carton.

Note: This information can be found in your Clipsal pocketbook right next to the part code.

Yes, there is the 93ER and also the 249/12 or 249/25.

No, they are only available in grey.

This applies to the 280/16 (16mm), 280/20 (20mm), 280/25 (25mm), 280/32 (32mm), 280/40 (40mm) and 280/50 (50mm).

The 265 series is a range of IP56 rated insulated boxes suitable for numerous junctions and terminations. Each box is supplied with a 3mm sealing gasket.

This applies to the 265/1, 265/3, 265/4, 265/5, 265/7 and 265/7D.

No it doesn't have a rating as such, however it is UV resistant.

The part number for the screws would be 265SCREW.

No, the 252/32/2A only comes in grey.

Yes, they can be fitted to C60 MCB's and RCCB's.
They come in a pack of 2 x 4 screw covers.

Yes, we can offer the 265/1 in electric orange. The part number is 265/1-EO.
Some of the key features are:

• Surface mount
• Dimension: 77 mm Length x 77 mm Width x 54 mm Height
• 63.5 mm screw centres C, 63.5 mm screw centres D
• Weatherproof, full cover plate

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=265/1


 

The replacement for a Merlin Gerin Shunt Trip Release MX + OF 26946 is a A9N26946.

The dimensions for a 261S Saddle Spacer are 261S are:

Saddle Spacers
Catalogue Number	Size	Length (L)	Width (W)	Centres (CRS.)	Standoff (T)	Height (H)
261S16	16mm	55mm	21mm	32mm	8mm	14mm
261S20	20mm	61mm	22mm	40mm	8mm	14mm
261S25	25mm	74mm	26mm	48mm	8mm	14mm

Saddles Spacers set a conduit run off the wall 8mm to allow easier cleaning and repainting and to facilitate entry into equipment. They are available in sizes 16mm through 25mm.
Standard colour is Grey (GY), with Orange (EO) also available at extra cost.

For further information please visit www.clipsal.com/Trade/search-results?q=261S

---

 

Issue:
How to change the display of an ATV320 to show RPM?

Product Line:
ATV320 series drives.

Environment:
All models, All serial numbers.

Cause:
Information unavailable or unclear in current literature.

Resolution:
The ATV320 drive cannot directly display the RPM of the motor, but we can use a custom configuration to display a number that is very close to the true motor RPM.

The drive normally displays motor speed in Hz.  In order to convert this to RPM, we much enter a custom multiplier.   You will need your motor nameplate information for this.

Take the actual RPM of the motor, as listed on the motor nameplate and divide that by the base Hz of the motor.  An 1800RPM motor want be exactly 1800, there will be a number such as 1750 or 1760 listed as the RPM.  Divide this number by the base frequency of the motor, usually 60.0Hz, to yield a multiplier of 29.3 for a 1760 motor, or 29.16 for a 1750 RPM motor.

Program parameter SDS (Scale Factor Display) under the DRC menu to this value. 

Note that if you are using the keypad of the drive to adjust the motor speed (FR1 or FR2 set to A1U1), you will only be able to show the speed reference on the display, you can not switch to display any other value in the drive while using the keypad to adjust speed.

The replacement for 26946 is A9A26946. However this is only good for Acti 9 Circuit breakers.
Wherefore if you where using the C120/C60DC range the replacement should be A9N26946.

For more information please visit https://www.schneider-electric.com.au
Or see PDFs attached.

MX Shunt trip                                                                Voltage Release