The keys for part number 30TKM are only available as a special.
We don’t do them as a standard part.
Not available, you can use the Clipsal 30TKM this can be fitted in a single VH plate (C2031VH)
It is 2 Way if you use it with a 60TSSM
No, unfortunately this mechanism does'nt fit the Saturn series. However, this mechanism will fit into the coms Saturn series comunication plate 4031VH.
You need to use part codes 4062TC + 2 x 60TSM
Part no 60tdm can be used as per wiring diagram for 2 way switching
Not available as complete. Use 2 x 30PFM and a 2 gang plate
No, Not Available in Black
To obtain a surge protected 15A outlet you will need to purchase a C2015/15X and a 30SFM and replace the extra switch in the outlet with the 30SFM surge protector mechanism and then wire accordingly.
For some reason we have given the 30CSFM a 10A rating. The mechanism only needs to be rated for the correct voltage and correct fault current the amperage rating is irrelevant as this device does not have the load passing through it, it is there merely for fault conditions.
Unfortunately, it only suits Saturn 1 touch series, not Saturn 4000.
The 60TDM is now available after going under a redesign. We also have the 60TDSM which is the slave dimmer mechanism which would be suiatble for 2-3 way dimming applications.
Slimline fits all 30 Series mechs. Permanent connection unit is the 38TB, phone mech is 30BTM
Any 30 series Clipsal mech will fit. 30BTM is the telephone mech, available in white only. 30FFPFMS is the TV mech.
You can use 4030VH plates and the 30 series mechs i.e. VDIB17735U, VDIB17756U, VDIB17736U & 30BTM
No. Our Draftstoppa only suits round exhaust fans up to 300mm diameter.
The Configuration Chart for the Saturn OneTouch range is:
4061TC (1 Gang Grid and Cover Only)
4062TC (2 Gang Grid and Cover Only)
4063TC (3 Gang Grid and Cover Only)
4064TC (4 Gang Grid and Cover Only)
4066TC (6 Gang Grid and Cover Only)
4061ATC (1 Gang Architrave Grid and Cover Only)
4062ATC (2 Gang Architrave Grid and Cover Only)
All of the above Cover plates can be configured to be Switches or Dimmers to your requirements by ordering the Grid & Cover plate and
then the matching OneTouch Dimmer or Switch. 60TSM (OneTouch switch 400W) or 60TDM (OneTouch Dimmer 350W)
B12/30/6 = 12-Gang Switch Plate. 2 rows of 6. Stainless steel. 303mm 120mm
12/30/162/3 = 12-Gang Switch Plate. 4 rows of 3. Stainless steel. 165mm 215mm
Includes stainless steel fascia with grid and wall box. Standard grid colours - White Electric (WE) and Black (BK).
The 60TDM is a touch mechanism and is suited to the OneTouch series wherefore the 4061E2PUDM is a push button mechanism suited to the Saturn series.
Please note these mechanisms are NOT interchangeable between series.
Part codes 4063TC + 3 x 60TDM
Yes , it is rated to 16AX for fluro based loads.
30USM-WE = Universal switch mechanism 20/16AX - compared to the 10A only 30M-WE
(see attached 30USM Brochure)
Screw B.S M3.5 X 0.6, 5.6mm CH HD IN
Part number replaced with 30USM mech but marked 'Heat' is not standard.
Yes, the jumper needs to be removed from the 60TDM, for 2 and 3-Way switching situations.
Yes, the operation of this light consists of short press "On", short press "Off", long press " Ramp down" long press "Ramp up".
You can use a Clipsal 7106A or 7108A both have a 230mm cut out and are 271mm square
If you want 2 stove switches in one plate, you would need to use Clipsal 4032VH and 30M35 and for the telephone use a 30BTM and 4031VH