capacitor load correction

CAPACITOR LOAD CORRECTION

Catalogue Number: 31CAP
capacitor load correction
Colour:
Colour: Per UOM Std.
  • 1 PCE 1

Specifications

hide show
Product brand
Clipsal
EU RoHS Directive
Compliant
Circularity Profile
N/A

Frequently Asked Questions

hide show

What is the code for the load correction device for OneTouch

 The part code 31CAP

Can you use a 31CAP on the 750WPR 3 wire sensor?

Yes, the 31CAP can be used on both 2 wire and 3 wires sensors.

For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP

What are the characteristics of a 31CAP capacitor?

The characteristics of a 31CAP capacitor are:
Values Description
Amp 0.025A (Ampere)  =  25mA (Milliampere).
Watts 6W
Voltage 240V
Microfarad 0.33μF
Maximum amount stacked in parallel 3

For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP

Can you use the 31CAP on a Leading Edge Dimmer?

No, the Leading Edge dimmer has a maximum input capacitance of 300nf, you would be able to use the 31LCDA as an alternative.
Trailing Edge and C-Bus Universal dimmers do not have a capacitance limit and either can be used.

I have 2 wire 31VETR and i dont have enough load will a 31CAP do the trick?

It will improve the situation however we cannot confirm wether it will fix the problem or not. The alternative is to use the three wire design 31VETR3

What is the rating of the 31CAP?

The rating of the 31CAP is 10nF (Nanofarads).



 

What is the minimum load required by the 2 wire infrascan?

The minimum load for a 2 wire infrascan is 40W. If the load is less than this you can use a 31CAP wired in paralel across the load.

Can a 751 be used with 25W LED?

Yes, it can but you will need to put a 31CAP in parallel with the load.

 

I have Saturn series LED switches in two way configuration that pulse when load is switched off

This can be corrected with the use of a 31CAP load correction Capacitor.

For further information on this product please visit the Clipsal website on the  link below
https://www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP
 

How many Farads is the 31CAP?

The Farad rating of the 31CAP is 10nF (Nanofarads).

For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP

Why wont the 753SSR sensor turn off the lights, it is wired to a contactor?

Even though this is a 3 wire device it still has leakage current and enough to keep the contactor energised therefore your lights will remain on. The way to prevent this is to use a 31CAP in parralell with the load. This will provide an alternate path to neutral.

What is the difference between the 31Cap and 31LCDA?

The 31CAP is a load correction device which consists of a"Capacitor only " to help 2 wire products achieve minimum load levels. The 31LCDA has circuitry built in to the device  to enable it to correct minor compatibility issues found between dimmers and Led downlights for example slight flickering when dimmed at a higher level.



31CAP - Corrects the load for 2 wire devices.


For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP



31LCDA - Helps with compatibility issues.



For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=31LCDA

Will a 2-wire Infrascan 750WP Sensor operate with 20W load?

No, Unfortunately a 20W load will not operate a 2-wire Infrascan 750WP Sensor as it has a minimum load of 40W. You can increse the minimum load by adding multiple lights or a larger light. Alternatively you can install a product called a 31CAP which is a capacitor specifically designed to "increase" the minimum load. 

The characteristics of a 31CAP capacitor are:
Values Description
Amp 0.025A (Ampere)  =  25mA (Milliampere).
Watts 6W
Voltage 240V
Microfarad 0.33μF
Maximum amount stacked in parallel 3

For further information please visit www.clipsal.com/Trade/Products/ProductDetail?catno=31CAP

 

Where should the Load correction devices 31CAP and S31LCDA be used?

The 31CAP is to be use with the following two wire products
Infrascan 750WP, 751, 753.
Timer 31VETR
Sunset Switch WS226SSR/2, 56SSR/2, 31VSSR/2

The S31LCDA is suitable for use with Clipsal & Schneider Electric 2-Wire, mains powered Dimmers that use
Leading Edge, Trailing Edge and Universal Dimming.
Other Suitable loads: Dimmable CFL/ Dimmable LED with Electronic control

(Load correction Devices may not correct all problems)
Installation Instructions can be found on the Clipsal.com Website.
 

Is there a gland on the back of the 319HP

 Yes there is

Is the intermediate size architrave switch still available?

Yes, the part number is 31BA.

What is the dimension of 31VA, 32VA, 33VA, 34VA, 35V and 36VA standard sized vertical flush switches?

31VA, 32VA,  33VA,  34VA,  35VA and 36VA standard sized vertical flush switches have a dimension of 115mm(length) x 73mm(width) x 11mm(depth). Mounting centres are 84mm apart. The switches are rated to 250V AC, 10A, 1 way/ 2 way.
For further information, please visit https://updates.clipsal.com/ClipsalOnline/Files/Brochures/A0000108.pdf

 

What is the part number for a surface mount enclosure to suit 319HP Pneumatic timer?

238/25 is a surface mount enclosure with 25mm end entries that will suit 319HP.

For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=238/25

What is the IP rating for the 319HP, pneumatic timer?

The IP rating for the 319HP, pneumatic timer is - IP65

For further information, visit the link below:-
https://www.clipsal.com/Trade/search-results?q=319HP
User-added image

 

What is the maximum time for a Clipsal 319HP time delay switch

Primarily designed for up to 10 minutes with care 20 minutes may be possible.

FYI We now have a range of new timers and time clocks modules which can be installed into any iconic plate or a installed and triggered by any momentary switch they can be installed placed inside the flush box

What is the part number for weatherproof / hose proof pneumatic timer?

319HP is the part number for weatherproof / hose proof pneumatic timer rated to 250V, 50Hz, 10A-6AX.
IP rating of 319HP is IP56.
For further information, please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=319HP