plate only 2gang 115mm sq

2 GANG SQUARE PLATE ONLY 115MM

Catalogue Number: 32/2V
plate only 2gang 115mm sq
Colour: White Electric
Colour: Per UOM Std.
  • White Electric 1 PCE 1

Specifications

hide show
Range of product
Standard Series
Product brand
Clipsal
Number of gangs
2 gangs
Product destination
switch
Fixing mode
by screws
Material
plastic
Marking
without marking
Mounting position
vertical
Fixing center
84 x 46 mm
Width
116 mm
Height
116 mm
Depth
11 mm
REACh Regulation
Reference contains Substances of Very High Concern above the threshold
EU RoHS Directive
Compliant
Mercury free
Yes
RoHS exemption information
Yes
China RoHS Regulation
Product out of China RoHS scope. Substance declaration for your information
Circularity Profile
N/A

Documents & downloads

hide show
Filter items
  • All

  • CAD Files and Packs

  • Installation Instruction

  • Product Environmental

  • Specifications

  • Certificates (MSDS)

Frequently Asked Questions

hide show

What mounting block suits the 39/2V?

The mounting block that suits the 39/2V is the 448.

Some of the key features are:
  • 8 mounting screw positions
  • Suits all switches and socket outlets with 115 x 115 mm fl ush plates and 84x46 mm mounting centres
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=448


 

Is there a 32/32 version of the 56E1 available?

No. There is only a 56E1/20/20 or 56E1/25/25 available.

Which version of the MBX drivers will work on a Windows8.1 32/64 bit OS?

Modbus+ Driver Suite (V8.0) and higher

What Microsoft Operating Systems were used to qualify Unity Pro v13.1?

Unity Pro v13.1 was qualified on the following operating systems:

Windows 7 32/64 bit
Windows 10 32/64 bit
Windows Server 2016



 

Does the PDL switch mech 687M10 switch DC 12/24 volts?

The switch mech 687M10 is not tested on DC switching and is NOT rated for DC circuits.

What is the part number of the mounting block suitable for 31/2VX large format blank switch plate?

The mounting blocks suitable for 31/2VX are
448 with dimensions of 120mm(Length) 120mm(Width) 28mm(Depth) 84mm x 46mm (mounting centres)
448SD with dimensions of 120mm(Length) 120mm(Width) 14mm(Depth) 84mm x 46mm (mounting centres)
For further information, please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448SD
448:

448SD:
User-added image
 

What is the part number for a square blank plate?

The part number for the square blank plate is 31/2VX-WE 115MM

For more information please visit https://www.clipsal.com/Trade/Products/flushplate
Or see Trade Product Guide Page # 84 Edition 92

What is part number for mounting clip to suit 25/2V?

The part number for mounting clip is a 154/2.

Will 25/2V double outlet, large size, vertical fit on 155P2 plaster bracket?

Yes, 25/2V will fit on 155P2. 25/2V is  Large Size Format 115 x 115mm, Double Power Outlet rated to 250V 10A.
For further information please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=25/2V
User-added image

155P2 is a large plaster mounting bracket with 84mm mounting centre. For further information please visit:
https://www.clipsal.com/Trade/Products/ProductDetail?catno=155P2
User-added image
 

What metal wall box suits the 39/2VA?

The wall box that suits the 39/2VA is 157/2.

Some of the key features are:
  • Sliding nut
  • 84 x 46 mm mounting centre
  • Suits universal wall construction
  • Horizontal and vertical mounting
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=157/2



 

What is part number for mounting block to suit 31/2VX?

The part number for mounting block to suit is a - 448

For more information on this part please refer to https://www.clipsal.com/Trade/Products/ProductDetail?catno=448

User-added image

How to use T_M_DIS_STD_CH_STS on BMXDDI3202K?

Question:
How can we use T_M_DIS_STD_CH_STS on BMXDDI3202K in terms of module diagnostic like TRIP, FUSE and Short Circuit?
 
Answer:
Structure T_M_DIS_STD_CH_STS  is the common structure reserved for DI/DO modules. However, not every bit is used for each module.
Trip function is only used on DO module, so as Short circuit.
Fuse Error could be realized in specific DI module, however it was not realized in DDI 3202K according to R&D.
 

What is the part number of the mounting block to suit 25/2V Standard range, double socket outlet, large size format 115 x 115mm?

448SD and 448 are the mounting blocks to suit 25/2V, Standard range, double socket outlet, large size format 115 x 115mm.  Dimensions of the mounting block are as follows:

For further information , please visit
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448SD
https://www.clipsal.com/Trade/Products/ProductDetail?catno=448
448SD
User-added image
448
User-added image
 

What modbus address or word shows you motor speed in rpm's on the ATV61 and ATV71 drives?

Issue:
What modbus address or word shows you motor speed in rpm's on the ATV61 and ATV71 drives?

Product Line:
Altivar ATV61 and ATV71

Environment:
All

Cause:
4X modbus address word showing rpm's motor speed.

Resolution:
rFrd= Output speed in rpm's modbus address 8604
rFr= Output frequency in hz modbus address 3202
Please note you might have an offset when reading the modbus addresses.

Is Unity Pro v10 supported on a Windows 7 operating system?

  Yes, Unity Pro v10 is compatible with Windows 7 32/64 sp1.
It is recommended that when launching UnityPro running on Windows 7 that you right click on the icon (executable) and "Run as Administrator".

 System with Microsoft Windows 7 Professional 32/64bits

System: Pentium Processor 2.4 GHz or higher, recommended 3.0 GHz
RAM memory: 2GB minimum; recommended: 3GB
RAM memory (using DTM or X80 drops) : 2GB; recommended: 4GB
Hard disk: minimum available free space 8 GB, recommended 20 GB
Microsoft Internet Explorer 5.5 or higher
On Windows 7 64bits System, installation of Windows 7 Service Pack 1 (SP1) is mandatory in order to use Unity Pro V10
 
Windows 7 Professional 64bits , with a minimum 4GB RAM memory is recommended for projects using DTMs

Is there a way to place a PowerLogic meter in test mode (demo mode) to simulate a load?

Issue 
Is there a way to place a PowerLogic meter in test mode (demo mode) to simulate a load?

Product Line
CM3000
CM4000
PM800    

Environment
Powerlogic meter modes

Cause
Simulating a load for a Powerlogic Meter

Resolution
The Series 3000, 4000 Circuit Monitor (CM3000 (CM3), CM4000 (CM4)) and the Series 800 Power Meter (PM800 (PM8)) have a load simulation mode that can be enabled. The 3 phase load simulation will be based on the CT and PT ratios that are in the meter prior to enabling the simulation. 
*Note: PM800 firmware revisions 12.000 and 12.200 do not support demo mode.

How to enable the simulation mode using SMS or a Modbus communication utility:
Write a decimal value of 2 to register 8001
Write a decimal value of 32320 to register 8000.

How to enable the simulation mode from the front panel display of the meter (refer to the device reference manual for instructions on Reading/Writing Registers):
Write a decimal value of 2 to register 8001
Write a decimal value of 32320 to register 8000.
Exit the register write mode but do not save changes. The meter will reset if changes are saved and the simulation mode will be disabled. 

The register write/read screen can be accessed by going to Maintenance (Maint), Diagnostics(Diag), Register (Reg) then entering the password, which is default 0. The register being written to can be changed by using the + soft key to increment the number by one. The <--- soft key can be used to increment the cursor by a factor of 10 (1 to 10 to 100 to 1000). Once the correct register is selected scroll down to the decimal value by pressing the ok soft key. Using the same procedure that was used to change the register value, change the value to be stored into the register. After the value is entered press ok until the cursor returns to the top.This will write the value to the register.

To disable the simulation mode:
Write a decimal 1110 to register 8000 or cycle control power to the meter.

What are the voltage, temperature and altitude tolerances for the Altivar 32/320 drive?

Issue:
Customer wants to know the temperature and altitude limitations for the ATV32/ATV320 drive. 

Product line:
ATV32, Altivar 32, ATV320, Altivar 320

Environment:
All

Cause:
n/a

Resolution:
The voltage range for the M2 drives (200-240V) is 200V, minus 15% to 240V, plus 10%.
The voltage range for the N4 drives (380-480V) is 380V, minus 15% to 480V, plus 15%.

The temperature rating for all models is +14F to +122F (-10C to +50C), without derating (as long as the switching frequency is 4 kHz or less). 

Optional derating is available from +122F to +140F (50C to 60C).  Consult the Installation manual for de-rating curves based on the temperature and switching frequency.

The maximum altitude the Altivar 32 can be installed without de-rating is up to 3300 feet (1000 meters).  De-rate the drive nominal current by each additional 330 feet (100m) up to a maximum ceiling of 10,000 feet (3000m). 

How can I tell if my ATV61 or ATV71 drive is in sleep mode? (Low speed timeout active).

Issue:
How can I tell if my ATV61 or ATV71 drive is in sleep mode? (Low speed timeout active).

Product Line:
ATV61 / ATV71 series drives.

Environment:
All models, All serial numbers

Cause:
Information not available in current literature.

Resolution:
A relay or logic output can not be configured to show this status.  In order to determine if the drive is in sleep mode, you will need to have a serial communication network connected to the drive.  Perform a read of parameter LRS3 (Logic address 3252 , 16#0CB4).  Bit 9 of this word will indicate whether the drive is asleep or awake.  If bit 9 is high, the drive is in sleep mode.  If low, the drive is in normal operation mode.

Can I use the XW+ AGS as stand-alone?

 The Auto Gen Start is not designed for stand-alone operation. It does not function in a simple system containing only an Auto Gen Start and a generator. The Auto Gen Start requires several other components for configuration and operation.

Generator - The generator should have automatic starting capability. Some manufacturers of generators without this capability may sell an optional automatic engine control module that will simplify operation with the Auto Gen Start. The generator should also supply a Generator Run signal, which the Auto Gen Start uses to detect whether the generator is running. Some generator manufacturers refer to this signal as the hour meter signal or Switched B+.
NOTE : Firmware revisions 2.3 and later do not require a dedicated run signal, rather it uses the presence of AC (AC2 input) to verify the generator has started. Type14 does not monitor a run signal at all.

Control panel - A separate control panel is required to configure the Auto Gen Start and monitor generator starting and stopping activity. The control panel also provides real-time clock information for the Auto Gen Start Quiet Time and Exercise Time features.

Network power : The Auto Gen Start requires a Xanbus power supply to operate. Network power is carried by the network cables, and is supplied by the inverter/charger. As a device that draws network power, the Auto Gen Start consumes a maximum of 3 watts.
 
Start and stop triggers - The Auto Gen Start requires a source of start and stop triggers for automatic operation. These triggers can come from:
• Thermostat 12/24 V input.
• Battery voltage, state of charge, and inverter load status. This information is transmitted over the network by the inverter/charger.
 

Which wall box suits the large size, twin socket outlet 25/2V?

The wall box that suits the large size, twin socket outlet 25/2V is 257D2-GY.
Its key features are:
  • 2 gang
  • 84 mm x 46 mm mounting center
  • Suits universal wall construction
  • With 20 mm cut-outs one end and 25 mm cut-outs at other, impact resistant, deep-type
For further information please visit https://www.clipsal.com/Trade/Products/ProductDetail?catno=257D2